Datamax E-3202 Instrukcja Użytkownika

E-3202Programmer’s ManualDatamax InternationalHerbert House12 Elizabeth Way, PinnaclesHarlow, Essex CM19 5FE UKPhone: +44 1279 772200Fax: +44 1279 424

6 E-3202 Programmer’s ManualESC E n : Turn emphasized mode on / offASCII: ESC E nHexadecimal: 1B 45 nDecimal: 27 69 n0 ≤ n ≤ 255This command turns

E-3202 Programmer’s Manual 7Print Position and Bit Image CommandsPrint Position commands:ESC $ nL nH : Set Absolute print positionASCII: ESC $ nL nH

8 E-3202 Programmer’s ManualESC W xL xH yL yH dxL dxH dyL dyH : Set printing area in page modeASCII: ESC W xL xH yL yH dxL dxH dyL dyHHexadecimal:

E-3202 Programmer’s Manual 9Bit image commands:ESC * m nL nH d1 ... dk : Select bit-image modeASCII: ESC * m n1 nH d1 … dkHexadecimal: 1B 2A m n1 nH

10 E-3202 Programmer’s Manual

E-3202 Programmer’s Manual 11Status CommandsGS a n : Enable / Disable automatic status Back (ASB)ASCII : GS a nHexadecimal : 1 D 61 nDecimal : 29 97 n

12 E-3202 Programmer’s ManualThird byte – paper sensor informationBit On/Off Hex Decimal Function0-1 Off 00 0 Paper roll near-end sensor : paperadequa

E-3202 Programmer’s Manual 13Printer statusBit On/Off Hex Decimal Function0 Off 00 0 Not used, Fixed to off1 Off 00 0 Not used, Fixed to off2 Off 00 0

14 E-3202 Programmer’s ManualEsc u n : transmit peripheral device statusASCII : ESC u nHexadecimal : 1B 75 nDecimal : 27 117 nn = 0,48Transmits the st

E-3202 Programmer’s Manual 15Bar Code CommandsThe following barcode symbologies are available with ESC POS: UPC-A (+2,+5), UPC-E (+2,+5), EAN 13 (+2,

Copyright Information:Firmware (Software) AgreementThe enclosed Firmware (Software) resident in the EPROM’s is owned by Licensor or its suppliers and

16 E-3202 Programmer’s ManualThese commands select a bar code symbology and print the bar code, m specifies the bar code symbology as follows:m Bar co

E-3202 Programmer’s Manual 17GS f n : Select printing position of human readable charactersASCII : GS f nHexadecimal : 1D 66 nDecimal : 29 102 nn = 0

18 E-3202 Programmer’s Manual

E-3202 Programmer’s Manual 19Macro Function andMechanism Control CommandsMacro Function Commands:GS ^ r t m : execute macroASCII : GS ^ r 00Hexadecima

20 E-3202 Programmer’s Manual

E-3202 Programmer’s Manual 21Miscellaneous Function andSpecific CommandsMiscellaneous Function Commands:GS P x y : Set horizontal and vertical motion

22 E-3202 Programmer’s ManualSpecific commands:Fs G nASCII : Fs G nHexadecimal : 1C 47 nDecimal : 28 71 nn = 0 font 12*24n = 1 font 9 * 24n = 2 f

E-3202 Programmer’s Manual 23Appendix ACharacter Sets:The following character sets are availableIBM and WINDOWS EMULATIONTable 437

24 E-3202 Programmer’s ManualTable 850Table 852

E-3202 Programmer’s Manual 25Table 857Table 860

iContents1Set of Commands...12Print and Line Spacing

26 E-3202 Programmer’s ManualTable 861Table 863

E-3202 Programmer’s Manual 27Table 869

28 E-3202 Programmer’s Manual

ii

E-3202 Programmer’s Manual 1Set of CommandsIf you wish to use BASIC, use CHR$ to send ASCII codes to the printer.Put the Decimal into brackets after C

2 E-3202 Programmer’s ManualCOMMANDASCIINote Name Function type HEX. DEC. PageESC u Transmit peripheral device status Status 1B 75 27 117 14ESC v Tra

E-3202 Programmer’s Manual 3Print and Line Spacing CommandsPrint Commands:LF : Print and line feedASCII: LFHexadecimal: 0ADecimal: 10LF prints the dat

4 E-3202 Programmer’s Manual

E-3202 Programmer’s Manual 5 Characters CommandsESC SP n : Set right side character spacing ASCII: ESC SP n Hexadecimal: 1B 20 n Decimal: 27 32 n E